Trade waste contains oil, grease, chemicals and solids. If you discharge directly to the sewerage network it can cause blockages and overflows, overload treatment plants and pollute our rivers and beaches.

So you don't cause any of these problems, you must:

  • have our approval to discharge trade waste to the sewerage network with a trade waste permit
  • apply for approval before you install pre-treatment
  • seek advice from a qualified Hydraulic consultant who has trade waste experience about what type of pre-treatment your business may require before you apply for your permit
  • use only pre-treatment equipment we have listed
  • use a licensed plumber to install the equipment
  • Unitywater does not own or maintain any of the pre-treatment devices.

Trade Waste Officer and business owner looking at grease arrestor

Commercial and service businesses 

Most require some form of pre-treatment, such as a grease arrestor, which removes some of the grease and fats, before their liquid waste is allowed to enter our sewerage infrastructure. See below. 

Industrial businesses 

Most require on site pre-treatment which must meet our acceptance criteria before discharging to sewer. The pre-treatment is customised to meet site specific requirements. See below. Read more about customised onsite treatment solutions

Pre-treatment requirements may include the following:

Industry

Details

Commercial food outlets or manufacturers

Food-generating businesses are usually required to install and maintain a grease arrestor of at least 1000 litres as a condition of a Trade Waste Discharge Permit.

The Trade Waste advisor that manages your permit application will assess whether your business needs a grease arrestor and will calculate the size required as per the hydraulic plan.

Education facility or childcare centres

Schools with science laboratories may need a grease arrestor, neutralising trap or dilution tank/s. Tuckshops or food preparation areas that produce hot food meals will likely require a grease arrestor and your Trade Waste advisor will assist in this matter.

Shopping centres

Garbage storage and bin washing areas need to have a silt arrestor of at least 1000 litres. The area must be ringed by a gutter in the ground or bunded. If the area is greater than one square meter, it needs a roof that overhangs the drain/bund by at least 900mm or a stormwater diversion system.

Mechanical workshop

Automotive and engineering industries are usually required to install and maintain an oil and solids/water separator of at least 1000 litres per hour capacity.

Each permit application will be assessed on the nature of oily waste to be treated, proposed treatment method and site location.

Hospital or Medical centre

Opticians, dentists, medical and veterinary surgeries may need one or all of the following: bottle trap strainers, plaster arrestor and/or silver recovery unit (for x-rays).

Laundromats

Laundromats need to install 1mm mesh lint screens. If temperatures are greater than 38°C, a cooling pit is required.

Industry and manufacturing

These include but are not limited to chemical manufacturers, pesticide manufacturers, metal finishers and regulated waste receivers. Your Trade Waste Officer is happy to advise you.

Trade waste and pre-treatment requirements

Not sure if you need a Trade Waste Permit? If your business does one of more of the following, you need a Trade Waste Permit.

  • discharges any liquid waste into Unitywater infrastructure, other than domestic waste (domestic waste is wastewater from a toilet, hand basin or sink)
  • washes up or cleans any utensil or equipment that is a component of the business and then discharges the wastewater into Unitywater infrastructure
  • has a commercial/industrial process that produces non-domestic liquid waste containing chemicals or residue from a commercial or industrial process).
  • has any existing pre-treatment devices installed on the property that will be connected to Unitywater infrastructure.

Some businesses may require a trade waste meter to measure trade waste discharge quantities. This will be outlined in each Trade Waste Permit.

A trade waste meter is a meter installed to measure the volume of trade waste discharge to the sewer and may be:

  • a water meter which measures the potable water entering the trade waste generating area or
  • a wastewater meter which measures the volume of trade waste discharged to the sewer.

Trade waste meters should meet the Queensland Plumbing and Wastewater Code and WSA 15-2014 Trade Waste Metering Code of Practice and be placed in a location that is accessible and does not poses a risk to the person reading the meter.

Trade waste meters are not required for all business. If a trade waste meter is required, details of the meter installation and maintenance requirements will be a condition of the Trade Waste Discharge Permit issued for the business.

Grease arrestor loadings are calculated using the grease arrestor sizing guidelines (PDF 46KB).

Find out more about trade waste pre-treatment facilities installation requirements via a trade waste pre-treatment facilities installation requirements fact sheet (PDF 374KB)

The cleaning frequency of these pre-treatment facilities will be specified in the Trade Waste Approval.

Please note: The cleaning contractor must supply a service record for each service carried out to Unitywater's Trade Waste team. This information must be in a format acceptable to Unitywater, preferably digital.

Unitywater does not own or maintain any of these pre-treatment devices. The permit owner is responsible for arranging a licensed private contractor (see liquid waste carriers) to service and maintain their pre-treatment device at the frequency specified in their approved permit. Evidence of this service in the form of a receipt from the permit owner is required by Unitywater to maintain approval of the permit. 

Hydraulic consultants are easy to find by searching online. They are also listed in the Yellow Pages under: Hydraulic Consultants and Services.

If you have already received approval from an authority other than Unitywater for a pre-treatment process, such as those below, please contact our Trade Waste team for consideration of your existing approval:

Grease arrestor: A grease arrestor is a device that will slow down the wastewater velocity to allow separation of greasy wastes. Grease arrestors must be serviced regularly (cleaning frequency depends on size, loadings etc.) to make sure blockages do not occur downstream or within the business premises.

Neutralising tank: Neutralising tanks are designed to accept laboratory wastes that have a high and/or low pH. The correct pH level allowed to be discharged is between 6 and 10.

Dilution tank: Dilution tanks are used generally as cooling tanks usually for commercial laundries that have wastewater that has high temperatures. The maximum temperature is 38 degrees Celsius. High temperatures can create hydrogen sulphides (rotten egg gas) that cause corrosion within the sewer network.

Approved lists (downloadable PDFs)